YD8116

YD8116

€68.50

  • Info
  • Service
  • Question
  • FAQs

The YaMoRC solution for switching and signaling: our 16-fold signal/switching decoder.

It presents the following features:

  • Sixteen independent 2.5Amp MOSFET outputs
  • Max 5 Amp combined current
  • Very simple basic-setup (base address), by pressing the programming button and switching the desired turnout address
  • No complicated CV settings.
  • Clear-text configuration based upon our new ES-Link technology.
    With our YD9101-Config or YD7100-Command, configuration can be done via built-in web interface: No need for PC-software or Phone/Tablet Apps!.
    - or -
    when using the classic Windows PC interface, the YD9100 config-USB-stick as well as our YD6016LN can provide the configuration.
  • All of the 16 outputs are freely configurable from 16x simple on-off to complex and elaborate signals with up to 8 LEDs/lamps
  • Each defined device (signal, switch, turnout) can have its own address
  • Devices can be operated by the new DCCext standard or conventional turnout DCC-commands (throw/close)
  • Numerous predefined signal definitions for Dutch, German (H/V, Ks and Form) British and Swiss prototypical signals
  • Signals can include fading (Bulbs emulated in case of LEDs) dark-phase inclusion, black-out based on previous signals state
  • Outputs can be time-limited e.g. for light coil-motors
  • Settable night-dimming for the complete decoder, with configurable address / decoder
  • Very suitable for motorized point motors.
  • Not suitable for solenoid point motors. For these motors, use our YD8008/YD8044.
  • For two-wire motorized point motors, like Conrad; Hoffmann; Tillig; etc. adapter YD6940 should be used.

How to configure the YD8116 with Viessmann signals and ECoS

Product Question

YD8044

By means of it’s powerful CDU the YD8044 can deliver up to 10 Amps to a connected coil.

Category: YD8044

Yes it can. That is, the YD8044 will sequentially switch the assigned turnouts in left to right order as seen in the image below.
Depending on how quickly the CDU will be recharged, the switching will appear more or less simultaneous.


Here Address #1 switches turnout on Out 1 and after that turnout on Out 2.

Category: YD8044

The YD8044 has very modest requirements on it’s power supply.
Due to it’s built-in CDU, the power supply never has to supply the switching coil-current. (which may be as high as 10 Amps)
The CDU charge current tops at a maximum of 350 mA at 19 V input voltage. So a 15 V / 0.5 Amp wall-wart adapter is fully sufficient to supply the YD8044.

Category: YD8044

Yes you can 🙂

Category: YD8044

In certain circumstances, the YD8008/8044/8116 modules can become “bricked”.
That means, they are not accessible anymore after a firmware update, configuration attempt or a settings import.

Usually that shows by not being “seen” anymore in the configuration program and/or no LEDs lighting up anymore.

The procedure to get your module “back to life” is this:
(the example is for the YD8116. For other modules substitute YD8116 with the name of your module)

ENGLISH

  1. look for YD8116.exe in the installation folder.
  2. connect the YD9100 to USB, but not yet to the YD8116.
  3. start YD8116.exe with a double-click.
  4. go directly to “ES-PGM” and click on “Update YD8116”.
  5. after a short moment the message “Connect your device in bootloader mode” will appear, do not yet click OK now!
  6. Press and hold the programming button on the YD8116.
  7. plug the YD9100 into the ES-PGM-LINK of the YD8116.
  8. as soon as the red LED lights up, click OK while the programming button is still pressed.
  9. when the green LED starts flashing rapidly, the button can be released.
  10. when updating is complete, click Restore factory settings.

DEUTSCH

  1. Suchen Sie im Installationsordner nach YD8116.exe.
  2. Verbinden Sie den YD9100 mit USB, aber noch nicht mit dem YD8116.
  3. starten Sie YD8116.exe mit einem Doppelklick.
  4. gehen Sie direkt zu “ES-PGM” und klicken Sie auf “Aktualisiere YD8116”.
  5. nach einem kurzen Moment erscheint die Meldung “Connect your device in bootloader mode”, klicken Sie jetzt noch nicht auf OK!
  6. Drücken und halten Sie die Programmiertaste am YD8116.
  7. stecken Sie das YD9100 in den ES-PGM-LINK des YD8116.
  8. Sobald die rote LED aufleuchtet, klicken Sie auf OK, während Sie die Programmiertaste gedrückt halten.
  9. Wenn die grüne LED schnell zu blinken beginnt, kann die Taste losgelassen werden.
  10. Wenn die Aktualisierung abgeschlossen ist, klicken Sie auf Werkseinstellung Zurücksetzen.

NEDERLANDS

  1. zoek in de installatie map naar YD8116.exe.
  2. verbind de YD9100 met USB, maar nog niet met de YD8116.
  3. start YD8116.exe met een dubbelklik.
  4. ga direct naar “ES-PGM” en klik op “Update YD8116”.
  5. na een klein moment verschijnt er de melding “Connect your device in bootloader mode”, nu nog niet op OK klikken!
  6. druk het programmeer knopje op de YD8116 in en houd deze ingedrukt.
  7. steek de YD9100 in de ES-PGM-LINK van de YD8116.
  8. zodra de rode LED brandt, klik op OK terwijl het programmeerknopje nog ingedrukt is.
  9. als de groene LED snel begint te flikkeren, kan het knopje losgelaten worden.
  10. als het updaten klaar is, klik dan op Fabrieksinstellingen terugzetten.
Categories: Products, YD8008, YD8044, YD8116

Load More