Product Tag: ES-Link

YaMoRC products with ES-Link capabilities

YD7652HS

YD7652HS

The YD7652HS is a position sensor board for use with all variants of Fleischmann turntables. The YD7652HS has been specially developed for turntables that no longer have ‘contact tabs’ on the bridge, which would otherwise make Basic-Plus operation (turning without the ‘click-clack’ sound) impossible. With this board mounted beneath the pit and a magnet beneath the turntable bridge, the bridge’s position is detected with pinpoint accuracy. It is also a cost-effective alternative to the YD7652ES sensor when there are more than 12 access tracks.

It presents:

  • 48 Hall-effect sensors, highly sensitive
  • Extremely strong neodymium magnet included
  • ES-Link connected directly to the YD7652 via an RJ45 cable
  • All fixing materials included
  • Available for both large and small Fleischmann turntables
  • Very simple installation and adjustment

YD7652ST-STEP

YD7652ST-STEP

The companion for the YD7652 to connect stepper-motor driven turntables.

It presents:

  • TCM2209 Silent Stepper-Driver.
  • Processor controlled driver-settings
  • Micro-Stepping from 8 to 256
  • Supply 12 – 19V
  • Max current 1.2A
  • Integrated connector for Home/Index sensor. ( Hall, IR, etc. )
  • Passthrough of bridge track-supply (with auto polarization) from YD7652.
  • Dynamic acceleration and braking.
YD7652EX-TURN

YD7652EX-TURN

The companion for the YD7652 to connect Roco and Märklin turntables.

It presents:

  • Connectivity for Märklin (old) and Roco H0 turntables.
  • Includes: RocoEdge-adapter, TURN-Link bridge, ES-Link bridge
  • Turntable-Type setable by jumper.
  • Provides ES-Link pass-through,
  • as well as an 8 Bit sensor module for signals from Roco- and Märklin turntables

Note: This module is also needed if you want to connect and use the Fleischmann/Roco 6652 / 665201 turntable. For that we also have a connector available on demand, please ask your dealer.

YD7432

YD7432

The YaMoRC solution for practically all polarity reversing tasks.

It presents the following features:

  • 2-sensor short-circuit free operation.
  • alternative short-circuit detection mode
  • follow polarity with external (LocoNet) occupation feedback
  • follow polarity with turnout at entry
    • via LocoNet
    • via DCC
  • set turnout at exit
  • 100% solid-state, no relays
  • RailCom Block-, Address and Rail-Direction Report
  • LocoNet occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity
  • ES-Link occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity
  • ES-Link configuration
  • Firmware updatable
  • Current Ratings:
    • 2A – Continuous Operation
    • 2.5-2.75A Short Circuit Detection treshold. For reversing as well as short circuit shurdown.
    • 3.5A – Maximum Current during maximum 5 Seconds ( Command Station/Booster should switch off in this time )

YD8248

YD8248

The YaMoRC solution for operating RC-Servos.

It presents the following features:

  • 4 Servo connections in standard configuration, each servo has:
    • Analog input for position and/or configuration
    • 4 Digital Inputs for analog/conventional control of up to 4 positions. ( no need of a digital command station !! )
    • Selectable servo travel: 90 or 180 degrees. Supports 90’and 180′ servos.
  • Up to 4 Frog polarization relays ( option Adapter YD8290 ) for the 4 Standard Servos
    • Frog polarization by 2 independent relays, both are off while servo moving to prevent short circuits on “difficult” turnouts.
  • up to 12 Servos in total by using option Adapter YD8291
  • Eight independent 2.5Amp MOSFET auxiliary outputs
    • selectable “common-voltage” between 5V or the rectified input voltage.
    • Max 2.5 Amp combined current.
    • Complete aspect configuration like in our YD8116
  • Very simple basic-setup (base address), by pressing the programming button and switching the desired turnout address
  • No complicated CV settings.
  • Clear-text configuration based upon our new ES-Link technology.
    • using the classic Windows PC interface, the YD9100 config-USB-stick
    • as well as our YD6016LN/RB and …
    • as well our YD7001 and YD7010 Command Stations can provide the configuration
    • All of the 8 outputs are freely configurable from 8x simple on-off to complex and elaborate signals with up to 8 LEDs/lamps.
  • Each defined device (Servo, Signal, Switch, Turnout) can have its own address
  • Devices/Servos can be operated by the new DCCext standard or conventional turnout DCC-commands (throw/close)
  • Not suitable for solenoid point motors. For these motors, use our YD8008/YD8044.
  • The auxiliary outputs are also very suitable for motorized point motors. For two-wire motorized point motors, like Conrad; Hoffmann; Tillig; etc. adapter YD6940 should be used.

https://youtu.be/1ezeb-E7c1s?si=63nhhq7G2w56ZYPe

YD7010

YD7010

Building on the immense succes of our YD9401 upgrade for the DR5000, we decided to bring a complete Command Station, the YD7010, that includes the proven YD7001 technology and YD9401 Network Module.

The command station is based on the technology used in our YD7001-E, but with a completely new designed mainboard, with improved component choice and PCB layout to render robustness and extended functionality. Of course the YD7010 comes with our YD9401 is pre-installed.
Further we improved some visual and usability aspects: Different colors for the RJ connectors which were easy to confuse when they were all gray. Now the XBus and Network sockets have different colors to the ES-Link/s88N, LocoNet and BBus connectors.
On the front we moved the GO- and STOP-LEDs to be in-line with all LEDs and that prevents touching and/or damaging the LEDs when operating the pushbuttons.
On the back we moved the RS-Bus and Program-Track terminals into one 4-way block. This effectively prevents the terminals of turning and, worst case, shearing off !

The product placement of the YD7010 in our portfolio is meant to be an Entry Level, yet very complete and versatile DCC command station.

A summary of the presented features:

  • Unique DCC signal generator:
    – With priority control and interleaved packet generation.
    – Changes sent  by any interface are directly being reflected to the track.
    – Generates RailCom Cut-Out.
  • 3 A integrated Booster
  • Operating voltage range from  15 – 19 VDC. Giving a track-voltage of 13.8 – 17.8 Volts. That means safe for your N-scale equipment and powerful for H0.
  • Multiple Model Railroad compatible Interface Busses:
    – LocoNet, the world standard set by Digitrax Inc.
    – XpressNet, from the inventor of DCC: Lenz
    – Good old S88 signalling, fully compatible with ES-IN-Link by use of our YD6902-EXT adapters.
  • USB interface for three virtual COM-ports:
    –  YD.Command **
    –  LocoNet
    –  XpressNet
    The USB connection can also be used to update the YD7010`s firmware
  • Full network capabilities:
    – WiFi Access Point,
    gives direct access to smartphones, tablets and handheld controllers
    – 100baseT RJ45 wired network socket,
    connect and bind to your home network and reliably connect your PC software
  • By means of the built in YD9401 Module which provides:
    – 6 different but SIMULTANEOUS usable network protocols on WiFi and LAN:
    *    XpressNet-LAN,
    *    Z21®,
    *    LocoNet Binary,
    *    LocoNet LBServer,
    *    JMRI: WiThrottle
    *    YD.Command **
  • Booster Interface by LocoNet-B with strong, 800mA LocoNet RailSync signals
  • Handcontroller, feedback modules etc. interface by LocoNet-T with strong, 800mA 12VDC power supply
  • Powerful 1 Amp XpressNet supply
  • Roco R-BUS compatible feedbacks on XpressNet socket
  • Roco B-BUS for compatible boosters on RJ10 socket
  • Lenz RS-BUS compatible feedbacks
  • Infra-Red sensor for the use of IR-based remotye controllers like the Uhlenbrock IRIS or the Piko DigiFern
  • Clear LED indicators
  • Programming:
    – POM write
    – Service Mode ( programming track )
    – ES-Link  capable modules like YD8044, YD8008, YD8116, YD6016ES, YD7403
  • Additional extra purchasable , quality made, YaMoRC spec,  switch mode power supply with choise of:
    – 15V fixed / 4 A
    – 18V fixed / 3.4A

**)
Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.

YD7001-E

YD7001-E

The YD7001-E ( Revision E ) is an intermediate solution to the delay of the YD7100+7101 Set.

Availability is very limited, please contact your dealer for details.

The command station is based upon a factory new DR5000 mainboard, which has been updated to solve some reliability issues. Furthermore our YD9401 is pre-installed and the hardware has an update to also measure Input- and Trackvoltages.

YD6016RB-CS

YD6016RB-CS

Our standard current-sensing feedback module with RBus / XBus Interface

It presents:

  • 16 current-sensing detectors, arranged in two independent blocks of 8, each with their own Common
  • 2 Amp continuous current per detector, 8 Amps in total combined over the 16 detectors on the whole module
  • 5 Amp short duration overload (100ms) capable per detector.
  • 1mA current sensitivity
  • Capacitive input filter on every input, to suppress noise on long cables and track-sections
  • Configurable on- and off-delay setting for each input for optimal de-bouncing in case of non optimal wheel-track contact
  • Every input individually configurable for various actions like feedback, turnout toggle, turnout throw, turnout close
  • Every input individually configurable for turnout-address
  • ES-IN-Link for direct connection of up to 4 additional YD6016ES modules (effectively creating a 80 input RBus module)
  • ES-IN-Link connection to other ES-Link enabled modules for module-configuration
  • ES-IN-Link connection to YD9101 for web-based configuration
  • USB connection with one Virtual COM port for the YD.Command** protocol
  • Firmware updatable over USB
  • Power supply directly from RBus / XBus ( or USB for easy configuration and updating on a PC )
  • Experimental: XpressNet feedback reporting. This enables more then 160 feedbacks on the white z21® command stations.

**)
Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.

YD6940

YD6940

A set of 2 adapters to connect turnout-motors that require polarity change to operate.
More commonly named as motor- or stall-drives.

Suitable for a.o. motor drives operated on our YD8116:

  • Conrad
  • Hoffmann
  • Tillig
  • Fulgurex
  • Tortoise
  • Cobalt Analog

Also for solenoid drives from Kato, operated on our YD8008 or YD8044

The Adapter can handle currents up to 3A

YD6942

YD6942

A set of 2 adapters to connect so called Common-Cathode ( minus-return ) signals to our YD8116.

The adapter comes with an onboard 270 Ohms series-resistor.
Thus effectively limiting the output current to about 50-70 mA depending on the supply voltage.