Product Tag: LocoNet

YaMoRC modules with LocoNet connection

YD7100+YD7101 Set

YD7100+YD7101 Set

The ultimate combo for your layout !

YD7100 Command Station + YD7101 Interface Extension, together presenting unparalleled features.

And… also not unimportant, it saves some buck compared to separate purchase.

YD7910

YD7910

The ultimate LocoNet Gateway module.

It presents :

  • WiFi/WLAN accesspoint for standalone operation without the need for an external router
  • LAN 100baseT Ethernet port to integrate the gateway in your home network
  • Infra Red RC5 Receiver
  • USB interface over two virtual COM ports, one with LocoNet®, one with YD-Command
  • Z21®, LocoNet Binary and WiThrottle protocols on WiFi and LAN
  • ES-IN-LINK for direct-connection of our YD6016ES feedback modules
  • Strong 32-bit ARM processor
YD7403

YD7403

The power-house of the YD7x family,

It presents:

  • Universal 3.5 Amp booster.
  • Fully galvanically isolated on all, defacto industry standard inputs:
    – LocoNet – B
    – Roco B-BUS
    – DCC-CDE
    – Track Sniffer
  • Automatic input selection
  • LED indication of currently active input
  • Local GO / STOP button to start/stop the booster, or reset in case of local short circuit
  • Follows input RailCom Cut-Out to it\\\\’s output
  • ES-PGM-LINK for easy configuration

Power:

  • Input 15-19 V DC
  • Output 3.5 A through cool H-Bridge MOSFET technology. ( no heatsink needed )
  • Short circuit protected
  • Automatic short-report over LocoNet, CDE channel or BBus interface.
  • H-Bridge Temperature measurement
  • Track-Current measurement
DR5033 Update

DR5033 Update

The firmware update that fixes the former Digikeijs DR5033 LocoNet problem, that caused hanging-up the complete LocoNet on busy traffic.

DR4088LN Update

DR4088LN Update

The firmware update that fixes the former Digikeijs DR4088LN\\’s LocoNet problem, that caused hanging-up the complete LocoNet on busy traffic.

YD7912

YD7912

Our multi-functional LocoNet device.

It presents :

  • Repeater functionality from one opto isolated Protected LocoNet to two, independant Standard LocoNets
  • RailSync pass-through when connected to a LocoNet-B commandstation on the Protected Loconet
  • Standalone capability providing two independant Stand Alone LocoNets
  • USB Interface for Configuring and LocoNet protocol interfacing to any of the physical LocoNets over two independant virtual COM-ports
  • ES-PGM-LINK to configure the module with our YD9101 Module Configurator
YD6016LN-RC

YD6016LN-RC

The RailCom enabled feedback module.

It presents:

  • 16 independant local RailCom detectors
  • 1 general purpose global detector on Track-Output
  • For non-RailCom equiped locos or cars, the module also provides Current Sensing on each input.
  • 3mA currentsensitivity
  • ES-IN-Link for direct connection of additional YD6016ES modules
  • ES-IN-Link connection to YD9101 for web-based configuration
  • RailCom Channel 1 and Channel 2 address detection per channel
  • RailCom POM-read on all channels
  • RailCom QoS and Acutal Speed, as well as Container data
  • USB connection with two Virtual COM ports for YD.Command and LocoNet protocols
  • Using USB-LocoNet, the module presents all its inputs, including connected YD6061ES inputs as standalone LocoNet system
  • Every input configurable for feedback and block-address
  • Powerful 32 bit ARM Processor
  • Power supply directly from Track-Input
YD6016LN-GND

YD6016LN-GND

Our standard ground-input feedback module with LocoNet Interface

YD6016LN-OPTO

YD6016LN-OPTO

Our standard opto-input feedback module with LocoNet Interface

YD7101

YD7101

The IO interface-extension for the small DCC command station,

It extends the YD7100`s already impressive features and capabilities by even more interfaces and options.

It presents:

  • Integrated RailCom Global detector, enables a.o. decoder read-out by POM !
  • Switchable Track-Out and Program-Track connections.
    – Program-Track with full RailCom support
    – Program-Track drivable during normal operation
    – Track-Outs turned off during programming.
  • Infra Red remote control sensor, to support a.o. Uhlenbrock Iris and Piko DigiFern
  • LocoNet-T Socket with 1.5 Amps (the maximum current on an average RJ12 connector) of LocoNet power.
  • ES-Link for daisy-chaining even more modules
  • s88N Socket for traditional s88 modules
  • IO-Link for Hight-speed I2C extension modules, also daisy-chained.