Product Category: Command Stations

YD7432

YD7432

The YaMoRC solution for practically all polarity reversing tasks.

It presents the following features:

  • 2-sensor short-circuit free operation.
  • alternative short-circuit detection mode
  • follow polarity with external (LocoNet) occupation feedback
  • follow polarity with turnout at entry
    • via LocoNet
    • via DCC
  • set turnout at exit
  • 100% solid-state, no relays
  • RailCom Block-, Address and Rail-Direction Report
  • LocoNet occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity
  • ES-Link occupation of S1, Track and S2 feedback, as well as short circuit status and track-polarity
  • ES-Link configuration
  • Firmware updatable
  • Current Ratings:
    • 2A – Continuous Operation
    • 2.5-2.75A Short Circuit Detection treshold. For reversing as well as short circuit shurdown.
    • 3.5A – Maximum Current during maximum 5 Seconds ( Command Station/Booster should switch off in this time )

YD7010

YD7010

Building on the immense succes of our YD9401 upgrade for the DR5000, we decided to bring a complete Command Station, the YD7010, that includes the proven YD7001 technology and YD9401 Network Module.

The command station is based on the technology used in our YD7001-E, but with a completely new designed mainboard, with improved component choice and PCB layout to render robustness and extended functionality. Of course the YD7010 comes with our YD9401 is pre-installed.
Further we improved some visual and usability aspects: Different colors for the RJ connectors which were easy to confuse when they were all gray. Now the XBus and Network sockets have different colors to the ES-Link/s88N, LocoNet and BBus connectors.
On the front we moved the GO- and STOP-LEDs to be in-line with all LEDs and that prevents touching and/or damaging the LEDs when operating the pushbuttons.
On the back we moved the RS-Bus and Program-Track terminals into one 4-way block. This effectively prevents the terminals of turning and, worst case, shearing off !

The product placement of the YD7010 in our portfolio is meant to be an Entry Level, yet very complete and versatile DCC command station.

A summary of the presented features:

  • Unique DCC signal generator:
    With priority control and interleaved packet generation.
    Changes sent  by any interface are directly being reflected to the track.
    Generates RailCom Cut-Out.
  • 3 A integrated Booster
  • Operating voltage range from  15 – 19 VDC. Giving a track-voltage of 13.8 – 17.8 Volts. That means safe for your N-scale equipment and powerful for H0.
  • Multiple Model Railroad compatible Interface Busses:
    LocoNet, the world standard set by Digitrax Inc.
    XpressNet, from the inventor of DCC: Lenz
    Good old S88 signalling, fully compatible with ES-IN-Link by use of our YD6902-EXT adapters.
  • USB interface for three virtual COM-ports:
    –  YD.Command **
    –  LocoNet
    –  XpressNet
    The USB connection can also be used to update the YD7010`s firmware
  • Full network capabilities:
    WiFi Access Point,
    gives direct access to smartphones, tablets and handheld controllers
    100baseT RJ45 wired network socket,
    connect and bind to your home network and reliably connect your PC software
  • By means of the built in YD9401 Module which provides:
    6 different but SIMULTANEOUS usable network protocols on WiFi and LAN:
    *    XpressNet-LAN,
    *    Z21®,
    *    LocoNet Binary,
    *    LocoNet LBServer,
    *    JMRI: WiThrottle
    *    YD.Command **
  • Booster Interface by LocoNet-B with strong, 800mA LocoNet RailSync signals
  • Handcontroller, feedback modules etc. interface by LocoNet-T with strong, 800mA 12VDC power supply
  • Powerful 1 Amp XpressNet supply
  • Roco R-BUS compatible feedbacks on XpressNet socket
  • Roco B-BUS for compatible boosters on RJ10 socket
  • Lenz RS-BUS compatible feedbacks
  • Infra-Red sensor for the use of IR-based remotye controllers like the Uhlenbrock IRIS or the Piko DigiFern
  • Clear LED indicators
  • Programming:
    POM write
    Service Mode ( programming track )
    ES-Link  capable modules like YD8044, YD8008, YD8116, YD6016ES, YD7403
  • Additional extra purchasable , quality made, YaMoRC spec,  switch mode power supply with choise of:
    15V fixed / 4 A
    18V fixed / 3.4A

**)
Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.

YD7460-18

YD7460-18

18V 3.3 Amp Switch mode powersupply.

– Double Isolated
– “Schutzklasse 2”
– Short circuit protected/shutdown
– Overload protected/shutdown
– “Cool” technology, does not heat-up when command station/booster is idle
– Small form-factor
– Real two-conductor low-voltage cord, no thin coax cable
– Made to our own specification, to match our boosters and command stations
– 18 V version

YD7460-15

YD7460-15

15V 4 Amp Switch mode powersupply.

– Double Isolated
– “Schutzklasse 2”
– Short circuit protected/shutdown
– Overload protected/shutdown
– “Cool” technology, does not heat-up when command station/booster is idle
– Small form-factor
– Real two-conductor low-voltage cord, no thin coax cable
– Made to our own specification, to match our boosters and command stations
– 15 V version, suited for TT scale and smaller

YD7001-E

YD7001-E

The YD7001-E ( Revision E ) is an intermediate solution to the delay of the YD7100+7101 Set.

Availability is very limited, please contact your dealer for details.

The command station is based upon a factory new DR5000 mainboard, which has been updated to solve some reliability issues. Furthermore our YD9401 is pre-installed and the hardware has an update to also measure Input- and Trackvoltages.

YD7403

YD7403

The power-house of the YD7x family,

It presents:

  • Universal 3.5 Amp booster.
  • Fully galvanically isolated on all, defacto industry standard inputs:
    – LocoNet – B
    – Roco B-BUS
    – DCC-CDE
    – Track Sniffer
  • Automatic input selection
  • LED indication of currently active input
  • Local GO / STOP button to start/stop the booster, or reset in case of local short circuit
  • Follows input RailCom Cut-Out to it’s output
  • ES-PGM-LINK for easy configuration

Power:

  • Input 15-19 V DC
  • Output 3.5 A peak current, 2.75 A continuous.
  • Short circuit protected
  • Automatic short-report over LocoNet, CDE channel or BBus interface.
  • H-Bridge Temperature measurement
  • Track-Current measurement
  • Input- and Track Voltage measurement
YD7100

YD7100

Delay reason: The chips used for the DC-DC converters have been declared EOL. That means, the factory did not restart production after the chip-crisis. For us this means a redesign of the PCB and Software.
Please contact your dealer for alternative offers.

The smallest DCC command station on the market !

Small in form, but great in features and performance.

It presents:

  • Unique DCC signal generator:
    With priority control and interleaved packet generation.
    Changes sent  by any interface are directly being reflected to the track.
    Generates RailCom Cut-Out.
  • 3 A integrated Booster
  • Operating voltage range from  15 – 19 VDC. Giving a track-voltage of 13.8 – 17.8 Volts. That means safe for your N-scale equipment and powerful for H0.
  • Multiple Model Railroad compatible Interface Busses:
    LocoNet, the world standard set by Digitrax Inc.
    XpressNet, from the inventor of DCC: Lenz
    ES-IN-Link, the next thing after good old S88 signalling, fully compatible with s88N with our YD6902-EXT adapters.
  • USB interface for three virtual COM-ports:
    –  YD.Command **
    –  LocoNet
    –  XpressNet
    The USB connection can also be used to update the YD7100`s firmware
  • Full network capabilities:
    WiFi Access Point,
    gives direct access to smartphones, tablets and handheld controllers
    100baseT RJ45 wired network socket,
    connect and bind to your home network and reliably connect your PC software
  • By means of our YD9401 Module, provides:
    Built-in Webserver for configuring and operating the YD7100,
    with no need for PC or Phone/Tablet installed Software or Apps. Just runs from any browser !
    6 different but SIMULTANEOUS usable network protocols on WiFi and LAN:
    *    XpressNet-LAN,
    *    Z21®,
    *    LocoNet Binary,
    *    LocoNet LBServer,
    *    JMRI: WiThrottle
    *    YD.Command **
  • Booster Interface by LocoNet-B with strong, 800mA LocoNet RailSync signals
  • Powerful 1 Amp XpressNet supply
  • Roco R-BUS compatible feedbacks on XpressNet socket
  • IO-Link connector for Command Station extension like our YD7101
  • Clear LED indicators
  • Programming:
    POM write
    Service Mode ( programming track )
    ES-Link  capable modules like YD8044, YD8008, YD6016ES
  • Quality made  switch mode power supply included with choise of:
    15V fixed / 4 A
    18V fixed / 3.4A
  • Strong 32-bit ARM processor on 48 MHz

**)
Disclaimer: YD.Command is the internal YaMoRC communication protocol. It is not publicly open, nor does YaMoRC supply support 3rd parties to use it. Futher can it be subject to change on demand and at will of YaMoRC, without further notice or explanation.